5G NTN关键技术研究与演进展望

5G非地面网络（non-terrestrial network,NTN）技术是5G通信系统面向卫星通信和低空通信等新应用场景的重要技术，标志着5G技术应用从陆地通信走向了空间通信。首先分析了5G NTN和地面5G的差异点，包括网络架构、时频同步、HARQ和移动性管理等。进而介绍了3GPP Release 17的5G NTN标准进展及关键技术点与3GPP Release 18的5G NTN增强技术。最后展望了未来空、天、地一体化的技术演进。通过对5G NTN技术研究和标准分析，明确了5G和卫星通信融合的技术路线，并为后续6G空、天、地融合系统研究和设计提供基础。     

Cu掺杂对有序Sr3YCo4-xCuxO10.5+δ多晶的结构与物理性能的影响

采用固相反应法制备了四方Sr3YCo4-xCuxO10.5+δ(x=0~1.0)多晶。用热重-差示扫描量热分析,X射线衍射研究了多晶的有序化相变及结构。在固溶范围内(x=0~0.4),观察到有序峰(103)和(215),说明四方Sr3YCo4-xCuxO10.5+δ多晶为超结构,这是由于合成时在1000℃以上发生了吸氧(δ)有序化相变；当x=0.6~1.0时,978℃时在晶界处形成了单斜杂相,破坏了Sr3YCo4-xCuxO10.5+δ多晶的有序。当x=0~0.4时,多晶呈半导体输运行为。随着Cu掺杂量的增加,Co4+提供的空穴载流子浓度增大,电阻率明显下降；由于Cu的固溶,自旋熵增加,载流子浓度和自旋熵的共同作用使x=0~0.2多晶的热电势不变,x=0.4的热电势降低。并且Cu掺杂导致的晶格畸变使Co3+离子由高自旋态转变为高/低自旋混合态,磁化强度和铁磁转变温度(Tc)降低,磁结构由G-型反铁磁转变为铁磁。在进行二次烧结后,300K时电阻率明显降低,热电势为一次烧结的2倍,可能是二次烧结使多晶的有序化程度增大,提高了铁磁有序排列。     

基于SOI衬底的宽带低损耗声表面波滤波器研究

使用结构为42°Y-X LiTaO₃(600 nm)/SiO₂(500 nm)/Si的SOI衬底，通过抑制横向模式等优化设计，研制了单端谐振器和声表面波滤波器。经测试，谐振器的谐振频率为1.5 GHz，品质因数(Q)值高达4 000；滤波器的中心频率为1 370 MHz，插入损耗为-1.2 dB，1 dB带宽为74 MHz，相对带宽达到5.4%，阻带抑制大于40 dB，且温度系数在-55~+85 ℃时优于-9×10^-6/℃。该产品具有高频、宽带、低损耗、低温漂、高阻带抑制的特点，其性能指标优异，具有很好的实用性。     

混凝土结构的压电声波检测分析

本文介绍了混凝土结构的压电体波和表面波检测的主要进展,对两种压电声波检测的优缺点进行了总结。体波检测设备一般埋入混凝土内部,需要选择合理的检测部位,检测结果较为精确;声表面波检测无需选择特定的部位,但是检测深度有限。在实际检测工作过程中,可以联合两种方法相互验证。     

Simulations of NBI fast ion loss in the presence of toroidal field ripple on EAST

NBI fast ion losses in the presence of the toroidal field ripple on EAST have been investigated by using the orbit code GYCAVA and the NBI code TGCO. The ripple effect was included in the upgraded version of the GYCAVA code. It is found that loss regions of NBI fast ions are mainly on the low field side near the edge in the presence of ripple. For co-current NBIs, the synergy effect of ripple and Coulomb collision on fast ion losses is dominant, and fast trapped ions located on the low field side are easily lost. The ripple well loss and the ripple stochastic loss of fast ions have been identified from the heat loads of co-current NBI fast ions. The ripple stochastic loss and the collisioninduced loss are much larger than the ripple well loss. Heat loads of lost fast ions are mainly localized on the right side of the radio frequency wave antennas from the inside view toward the first wall. For counter-current NBIs, the first orbit loss due to the magnetic drift is the dominant loss channel. In addition, fast ion loss fraction with ripple and collision for each NBI linearly increases with the effective charge number, which is related to the pitch angle scattering effect.     

利用FDM和随机共振检测风机主轴承微弱旋转信号

轴承作为风力发电机设备中重要部件,其健康状态直接影响风力发电机运行的稳定性和现场的安全可靠性.由于风力发电机特殊的工作环境,导致采集到的振动信号中包含大量的噪声干扰,难以准确提取轴承振动信号包含的信息成分,给评估主轴承健康状态带来困难.因此本文采用将傅立叶分解(Fourier decomposition method,FDM)和随机共振(Stochastic resonance,SR)相结合的方式提取信号中微弱的轴承振动信息.首先用FDM将原始信号自适应地分解为一系列包含轴承振动特征的傅立叶频带函数,然后找出相关性大的频带函数进行重构,最后采用SR对重构信号进行分析获得特征频率,判断轴承的健康状态.结果 显示,将两种方法相结合能有效提高输出信噪比,提升特征频率检测的精度,为实现风机轴承早期微弱故障诊断提供帮助.     

Achieving fabrication of highly transparent Y2O3 ceramics via air pre-sintering by deionization treatment of suspension

An easy albeit quite effective deionization suspension treatment was adopted to alleviate the detrimental effects related to the hydrolysis of Y₂O₃ in an aqueous medium. Fabrication of highly transparent Y₂O₃ ceramics with a fine grain size via air pre-sintering and post–hot isostatic pressing (HIP) treatment without using any sintering additive was achieved using the treated suspensions. The hydrolysis issue of Y₂O₃ powder in an aqueous medium was effectively alleviated by using deionization treatment, and a well-dispersed suspension with a low concentration of dissolved Y³⁺ species was obtained. The dispersed suspensions were consolidated by the centrifugal casting method, and the green bodies derived from the suspension of 35.0 vol% solid loading showed an improved homogeneity with a relative density of 52.1%. Fully dense Y₂O₃ transparent ceramic with high transparency was obtained by pre-sintering consolidated green compacts at a low temperature of 1400°C for 16 h in air followed by a post-HIP treatment at 1550°C for 2 h under 200 MPa pressure. The sample had a fine average grain size of 690 nm. The in-line transmittance of the sample reached 83.3% and 81.8% at 1100 nm and 800 nm, respectively, very close to the theoretical values of Y₂O₃.